Purchased equipment: biomass boiler flue gas temperature
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

biomass boiler flue gas temperature

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

Biomass Flue System for GRANT NI Biomass Boile

The 25mm high efficiency Superwool blanket maintains flue gas temperature, maximising efficiency, improving flue draught on start up and minimising condensation. Low external case temperature. Inner liner held by the male locking collar but free to expand and contract with temperature by up to 18mm through the female collar.


The aim is to demonstrate that the efficiency of biomass boilers can be significantly improved by decreasing the temperature of the flue gases to levels at which condensation of combustion products occurs.

Recovery of Water from Boiler Flue Gas Using Condensin

The performance of boiler heat exchangers is limited by the need to keep the flue gas temperature above its dew point to avoid condensation of corrosive acids. However, latent heat can be recovered at temperatures below the dew point of the gas by protecting the heat exchanger tubes from the acids.

Gas cleaning in flue gas from combustion of bioma

Gas cleaning in flue gas from combustion of biomass condense and/or sublime during cooling in the boiler. Upstream of the gas cleaning installation, normally at a temperature < 200°C, we find all metals as solid particles, except mercury. Mercury evaporates during combustion and reacts Flue gas • Composition and temperature

Experimental investigation on flue gas emissions of

The flue gas flow rates during the boiler idle periods were expected to be too small to be measured by a common anemometer. In addition, the flue gas temperature was found to be too high for common anemometers. Thus, a flue gas flow rate/velocity calculation approach was first considered.

How to reduce the biomass fired boiler flue gas temperatu

Coal fired steam boiler temperature regulation In the operation of coal fired steam boiler,the temperature fluctuations can cause a range of hazards,the high temperatures will cause superheater tube wall temperature rise,the low temperature will affect the the gas consumption increase of gas users,even damage the equipment,so we need to

Testing of flue gas emissions of a biomass pellet boile

After the biomass boiler was ignited, the boiler was heated up and the flue gas temperatures gradually went stable within an hour. Fig. 6 shows the stable flame temperature of 981.8 °C, furnace chamber (hearth) 640.2 °C (thermocouple sensor outside the flame), flue gas 245.3 °C and boiler hot water 126.8 °C.

China’s first straw based biomass power pla

and a flue gas cooler. An air preheater is located outside the boiler. The air is preheated by boiler feedwater in order to prevent the low temperature corrosion of heat exchangers inside the rear pass that can occur if air is heated by flue gas (as in most other typical designs).

The Combustion Performance of Biomass Pellet Boiler

The flue gas stays in the high temperature combustion chamber for quite a long time, and after several times oxygen replenishment, the biomass pellets are fully burned, therefore, biomass pellets maintain high using rate, which solved the black smoke pollution problem perfectly.

Flue Gas Boiler - Waste Heat Boiler - Zhong Ding Boiler C

The high temperature flue gas generated by waste material or waste liquid flows into the furnace, working medium inside the boiler will take it into the front and end smoke chamber in order, then high temperature flue gas becomes low temperature flue gas, and then discharged into the atmosphere through chimney.

flue gas temperature in boiler | Sitong Wood Biomass Fire

Flue gas is the gas exiting to the atmosphere via a flue, which is a pipe or channel for conveying exhaust gases from a fireplace, oven, furnace, boiler or steam Flue Gas Spill Switches: Guide to Furnace or Boiler Flue