Purchased equipment: selection of boiler capacity
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

selection of boiler capacity
Others

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

Back to basics: Boiler selection - Consulting - Specifyin

It will assist with the selection of a burner that meets the needs of the boiler and the need for upstream equipment including heaters, separators, and pressure-control equipment. Boiler efficiency. It is the responsibility of the engineer and owner to define the desired efficiency of the boiler.

Selection and Sizing of Pressure Relief Valves - PDHonline.c

capacity has been certified by a designated agency, such as the National Board of Boiler and Pressure Vessel Inspectors. Adoption of the ASME Code by the States

The importance of the modulation ratio in the boiler

The selection of the model is connected to the new design load, but it is also bound to the nominal capacity of the equipment on sale, that is never below about 10 kW. Then it is of paramount importance the modulating ratio that is till which capacity the boiler can operate continuously without working in the inefficient ON–OFF control.

Parameters for Selection of Boilers | Boiler | Furna

Parameters for Selection of Boilers. B.G. Kulkarni SYNOPSIS Steam Boiler is a very important equipment for all process industries. There are many codes in use for design of boilers internationally. All these codes mainly take care of safety aspects of boilers from angle of mechanical strength.

A Large-Capacity Pressurized-Fluidized-Bed-Combustio

A Large-Capacity Pressurized-Fluidized-Bed-Combustion-Boiler Combined-Cycle Power Plant 108 All plant operations, from the start of the seawater system to the operation of the plant under a full load to the shut-down of the plant, were made sequential on a system-by-system basis to implement a fully-automated plant based on control computers. For

Boiler Calculations - K

1 Steam/water diagrams used in boiler calculations Temperature-heat (T-Q) diagram The T-Q diagram is a useful tool for designing heat exchangers.

Oil, Gas and Dual Fuel Burners - Oilon Group

• boiler capacity and efficiency, or required burner capacity • furnace back pressure • fuel/fuels to be used • burner inlet fuel pressure • burner capacity regulation method 2 Calculate the burner capacity. Burner capacity = boiler capacity / efficiency Example: boiler capacity of 2,500 kW, efficiency of 90 % →

Selection Scheme of Industrial Boiler for Steam Supply--Z

Selection Scheme of Industrial Boiler for Steam Supply 2018-12-11 11:04:29. Building materials industry, paper industry, textile industry, food sugar, rubber paper, petrochemical, medical and pharmaceutical industries, most of the production needs a certain temperature of heat to meet the production process requirements.

Boilers and burners combine correct

Boilers and burners combine correctly The need to save energy and reduce emissions makes boiler/burner capacity optimisation una-voidable. The best setup helps to keep boilers operating for decades with low damage and maintenance levels. In this writer’s opinion, the importance of diligently identifying the actual

(PDF) A Rule-Based Industrial Boiler Selection Syst

Boiler is a device used for generating the steam for power generation, process use or heating, and hot water for heating purposes. Steam boiler consists of the containing vessel and convection

Selection of 50 Ton Gas Steam Boiler--Z

Selection of 50 Ton Gas Steam Boiler 2018-05-15 16:13:20. A few days ago, a customer consulted us for the price and selection of 50 tons gas fired steam boilers. How to select 50 ton gas fired steam boilers? If the 50 ton gas fired steam boiler is used in production for steam, the optional type is SZS series gas boiler.

text