Purchased equipment: water tube boiler for heat recovery system
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

water tube boiler for heat recovery system

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

Heat recovery FAQ - Thermal Energy Internation

What is a FL  U-ACE hea  t recovery system?  FLU-ACE is a direct contact condensing heat recovery system. It recycles the heat normally lost through flue gas exhaust, and uses it to preheat a heat sink – this could be water for your space heating, domestic hot water, boiler feed water, or outside air heating.

Energy heat recovery system / for boilers - LUV

Find out all of the information about the GekaKonus GmbH product: energy heat recovery system / for boilers LUVO. Contact a supplier or the parent company directly to get a quote or to find out a price or your closest point of sale.

Boiler System Efficiency | Hvac | Water Heati

the economic and technical benefits of boiler heating system. using recovered heat at any time there Recent information on low-temperature are concurrent heating and cooling heating systems indicates that biocides loads. The combining of heat recovery should be part of the water treatment regi-

Boiler Blow down Heat Recovery - IOSR Journa

Plate type heat exchanger is used in the system, which is used to absorb heat from hot water. This heat is supplied to the boiler feed water. BOILER REQUIREMENTS A boiler is the one which generates steam above atmospheric pressure. A boiler is a closed vessel which generates steam by transferring heat produced by burning of fuel to water.

Boiler Economizer Exhaust Heat Recovery Syste

RTR - RECTANGULAR TUBE RECOVERY SERIES The RTR is ideal for large steam boilers and hot water boilers. The RTR is typically used to preheat boiler feedwater, process water, hot oil, or cold water condensing applications.

Horizontal Steam Drum | Water Tube Boiler | Heat Recover

Horizontal steam drum for steam-water reservoir in Heat Recovery System Generator. Expertise includes water tube steam drum and waste heat steam drum. Smaller volume results in reduced installation space, lower manufacturing and installation cost.


control provided through boiler water level control. Waste Heat Recovery From Furnace Gases Continuous Steam Waste Heat Job: Casting Engineers Chicago, IL System: Fume incinerator is used to burn core and mold gases 24 hours a day. Waste heat boiler uses heat tracing, external piping and internal coil to prevent freez-ing.

Waste heat recovery - Alfa Lav

waste heat recovery is to try to recover maximum amounts of ison is a BEM shell-and-tube system with stainless steel tubes and fusion bonded AlfaNova compact heat exchangers. For more details, please visit Consequently the boiler’s fuel consumption is reduced, as are

Boiler | Engaged in Thermodynami

The feedwater system is composed of two sources of water that deliver water to the boiler to be converted into steam. The feedwater consists of the condensate return water and treated makeup water. Feedwater heaters extract the waste heat from the spent steam to preheat the boiler feedwater.

Cannon Bono Energia | Heat Recovery Boile

The most common design of Cannon Bono Energia’s heat recovery steam generators is a water-tube, bi-drum, natural circulation structure (CTR series) which offers a capacity up to 60 MWt, steam pressure up to 70 bar and temperatures up to 550°C. This boiler design presents several advantages:

Firetube Waste Heat Boilers | E-Tech Heat Recovery Syste

Excellent for petrochemical and thermal oxidizer applications. Firetube boilers work by forcing exhaust gases through tubes immersed in water and represent the most economical means of generating steam from waste heat.