Purchased equipment: high medium pressure boilers in steam power plants
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

high medium pressure boilers in steam power plants
Others

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

Boiler Types and Classifications - Wiki - odesie by Tec

Boilers that operate higher than 15 psig are called "high-pressure" boilers. A hot water boiler, strictly speaking, is not a boiler. It is a fuel-fired hot water heater. The boiler feedwater is used as a cooling medium to reduce the steam to condensate, which increases the temperature of the feedwater and, In small steam plants, a

What is the typical pressure and temperature of LP, MP, H

It is high enough to drive reasonably-sized steam turbines, and provide high-level heat. (The condensing temperature at that pressure is ~485F.) Unlike power plants, industrial systems are open, meaning that most of the steam is not recovered as condensate and the system requires a lot of fresh make-up.

Boilers Boiler Technology | GE Steam Pow

Contact GE Power for more information on the use of boilers in steam power plants. Industry Leader in Supercritical and High Efficiency GE led the industry in developing supercritical steam generation technology, and is an industry leader in today’s high efficiency ultra-supercritical PC and CFB technology .

Difference Between Low- and High-Pressure Boilers | Hunk

High-pressure boilers are used in industries and designed to generate the steam found in power plants, dry cleaners and laundromats. These boilers were also used in locomotive steam engines to give them the necessary power to run.

Boiler (power generation) - Wikiped

A boiler or steam generator is a device used to create steam by applying heat energy to water.Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure (7–2,000 kPa or 1–290 psi) but, at pressures above this, it is more usual to speak of a steam generator.

MC Steam Boilers and Turbines for Power Plants

to Steam Boilers and Turbines for Power Plants maximum operating steam pressure required at the superheater outlet for operation of coke breeze to high and medium volatile bituminous. It is particularly efficient with free-burning type coals in the Mid-West producing areas and

Steam Power Plants | Boiler | Steam - fr.scribd.c

High Pressure Boilers • In all modern power plants, high pressure boilers (> 100 bar) are invariably used due to their inherent advantages. • If high pressure steam is used, plant efficiency is increased because lesser quantity of steam is required for generating a given power; i.e., work done per unit mass of steam is higher.

29315004 Steam Power Plants | Boiler | Ste

The steam is then condensed to water and pumped back into the boiler to repeat the cycle. In modern power plant. boilers produce steam at a high pressure and temperature. The steam is then piped to a turbine. The heat from combustion of the coal boils water in the boiler to produce steam. Coal is burnt in the boiler furnace to produce heat.

Development of Technologies for Improving Efficiency o

Since the 1990s, a series of supercritical pressure power plants have been built in Japan, with technologies for higher temperatures being developed, accumulated, and passed on. Improvements in the efficiency of coal-fired power plants are made by increasing the steam temperature and pressure, and plants currently under

High Pressure Piping in Power Plants – Water / Steam Cycl

2. High-Pressure Piping Systems Power plant typesPower plant types Water/steam cycles in thermal powerWater/steam cycles in thermal power plants are the connections between the feed water pumps, the boiler / heat exchanger and the turbine. Coal-fired power plants Lignite-fired power plants NuclearpowerplantsNuclear power plants

Boiler design for ultra-supercritical coal power plant

Modern coal-fired boilers used in power plants can be classified in various ways, according to their steam parameters, steam-water circulation, combustion method, or design configuration (Malek, 2005).

text